Learning of remote control without diagnose

You can learn the remote control without diagnose on some cars. Click on the right car to see the procedure description.

Learning of remote control Seat Ibiza (6K)

Learning of remote control VW Sharan/Seat Alhambra/Ford Galaxy 2000

Learning of remote control Audi A8 (4E)

Learning of remote control Audi A6 (4B)

Learning of remote control Audi A3 (4P)

Learning of remote control Audi A2 (8Z)

Learning of remote control, Audi –2000, Central lock

Used on Audi models until year 2000, with pneumatic central lock

Please follow these instructions:

  1. Remote Control Matching
  2. Turn the ignition key to ON and leave the key in the ignition lock.
  3. Lock the car from outside using the new, unmatched key in the driver-side door lock.
  4. Press the UNLOCK button on the new key within 5 seconds often enough to reach next memory position (so, if the value in field 2 was 0001, you should press the new key´s unlock button twice, to put the new key in memory position 2).
  5. The car may give you some sort of acknowledgement as the button is pressed (lights flash, horn beep, etc.)
  6. Wait 5 seconds and press the unlock button on the new key to unlock the door.
  7. Turn the ignition key to OFF and remove the old key.
  8. Press LOCK and UNLOCK with the new key.
  9. Insert the new key in the ignition and turn to the ON position (do not start car).

Learning of remote control Seat Ibiza (6K)

Note: On remotes with transponder TP48 is letter W (remotes with transponder TP5 fixed codes is without it).

Learning of the remote control(s)

  1. Turn ignition ON for max. 5 seconds with remote you want to be learned.
  2. Pull the key form the ignition.
  3. In the time of 20 seconds press the button OPEN, hold it pressed and 3 times press the button CLOSE…
  4. Release button OPEN and check the remote control lamp if it blinks 5 times.
  5. If the signal from remote control is accepted the central lock locks and unlocks the car and turn signals flashes.
  6. If you want to add more remotes, just repeat steps 3–4 within next 20 seconds (for every remote).
  7. Central lock confirms learning of remote either by locking or unlocking the car (depending on the state of central lock)-
  8. If the process is sucessfully ended, all remotes used before are erased from the memory. It means that all remotes need to be learned at once.

Learning of remote control VW Sharan/Seat Alhambra/Ford Galaxy 2000

Note: Remotes can be added by closed windows only. Adding of remotes should take time up to 15 seconds, not longer (read this instruction first)

Learning of remote control

  1. Insert key to the driver door lock and unlock three times. Every time hold the key 5 seconds in the unlock position
  2. Pull the key from the lock and press the CLOSE button on remote and hold it pressed.
  3. Three time press button OPEN.
  4. Release CLOSE button.
  5. Check if the remote control lamp blinks 5 times.
  6. To learn other remotes just repeat steps 2 and 3 within total time of 15 seconds.

Learning of remote control Audi A8 (4E) 2003–2008

  1. Turn the ignition on using the not working remote control. Remote is automatically learned.
  2. If no remote work at all check the receiving of the signal in control unit.

Checking of receiving signal in control unit

  1. Connect remote control unit – address 5 Access authorisation
  2. In the function Test signal of remote control check receiving and recognition of the signal (press the button on remote and follow the states of values)
  3. If the key is not recognized, disconnect the battery and repeat sequence.

Learning of remote control Audi A6 (4B) 1998–2002

  1. Open the car using drivers door lock.
  2. Turn ignition ON.
  3. Close (lock) the car with the drivers door lock.
  4. Within 5 seconds press button OPEN on remote control 1x or 2x or 3x or 4x depending on memory position you want to use (overwrite). Every press of button is confirmed by turn signals.
  5. Wait 5 seconds.
  6. Press again button OPEN. Car unlocks, remote is learned.
  7. Turn ignition OFF and pull the key.
  8. Press the button OPEN or CLOSE on remote control.

Note: Maximal number of remotes is 4. If you press the button CLOSE (in the phase of learning – within 5 seconds) all remotes is erase. You have to repeat the all the process in this case. Total time for learning of remotes is 30 seconds. You have to repeat the all the process in this case.

Learning of remote control Audi A3 (4P) 1997–2002

  1. Open the car with the drivers door lock.
  2. Press button OPEN on remote control.
  3. Turn ignition ON.
  4. Turn ignition OFF and pull the key.
  5. Press the button OPEN or CLOSE on remote control.

Note: Maximal number of remotes is 4.

Learning of remote control Audi A2 (8Z) 2001–2005

Control unit version up to 0999

  1. Press OPEN button on remote control
  2. Lock and unlock car using drivers door lock within 30 seconds.
  3. Check the function of the remote control (it should work now).

Control unit version 1000 (after year 2003)

  1. Open the car with the drivers door lock.
  2. Press button OPEN on remote control.
  3. Turn ignition ON.
  4. Turn ignition OFF and pull the key.
  5. Press the button OPEN or CLOSE on remote control.

Note: Maximal number of remotes is 4.

 

CzechEnglish